Call Us Nationwide 1-800-741-9956
Call a Pool Heater Expert Today
     
inquiry
  Shop for Pool Heat Pumps, Pool Heaters and Pool Heating Systems
Home About Contact Email FAQ Testimonials Ordering Shopping Cart Shopping Cart
Shop Pool Heat Pumps and Pool Heaters
 

Pool Heat Pumps
Pool Heaters
Heat Pump Price List

Heating & Cooling
Pool Chillers

Gas Pool Heaters

Geothermal

Electric

Solar

Above Ground

Indoor Pools

Refurbished
Manufacturers

International Heat Pumps

Clearance Heat Pumps

Discounts & Coupons

Shop Pool parts, supplies and accessories
 

Heat Pump Parts
Pool Supplies
Titanium Heat Exchanger
Control Boards

Capacitors

Compressors
Pressure Switches
Pool Cover Reel Systems

Solar Pool & Spa Covers

Heat Pump Covers

Pool Cleaners

Chlorinators

Pool Filters

Pumps

Control Systems

Resources
  Choosing a Pool Heater
Pool Heating Costs
How to Save Money

Delivery of a Heat Pump
Electric Heater vs. Heat Pump
Testimonials

Installation Photo's

Testimonials by State

International Electric Currents

Universal Currency Converter
Ventes Internacionales
International Customers
Canada
Partners
 

Installer Inquiry
Contractor Inquiry
Become a Dealer

 

Rome-Solarium Pool Heat Pump Troubleshooting

Download Rome-Solarium Owner's Manual

Check to see that the electrical power is on. Reset breakers, or replace fuses if necessary.

Check to be sure the electric control panel is set properly. The desired temperature must be set above the actual pool or spa temperature for the heater to run.

 

Check to make sure the evaporator coil has enough clearance and that there are no restrictions to its

airflow.

Certain ambient air conditions may cause the heater to go into defrost mode, displayed on the control panel as FS.

 

NOTE: IT IS NORMAL FOR WATER TO DRIP FROM THE DRAINHOLES AT THE BASE OF THE HEATER. THE UNIT PRODUCES CONDENSATE WHEN IT OPERATES.

Analyzer Codes

FAILURE LOCK-OUT: This feature is for the protection of the heater. If the same failure occurs three

(3) times within an hour, the control will not allow the unit to restart, and shall display the appropriate

code (i.e.FL3, HP3, or LP3).The reset to normal conditions can be accomplished by pressing a button on the control touch pad.

FLO (Little or No Water Flow)

The pump is not running.

The filter is dirty or clogged.

Shortage of water to pump - air leak.

Undersized pump.

Valves not in correct position.

Filter in backwash mode.

Water pressure switch needs adjustment, or is defective.

FL3

FIL MODE MUST BE IN THE OFF POSITION OR A FL3 ERROR CODE WILL BE DISPLAYED.

HP (Compressor High Pressure)

Low water flow to heater.

Defective high-pressure switch.

LP (Compressor Low Pressure)

Evaporator coil dirty.

Fan motor not running.

Low refrigerant pressure.

Defective low-pressure switch.

dPO Evaporator temperature sensor connection opened. Check for cut or loose sensor wiring or defective sensor.

 

PO Water temperature sensor connection opened. Check for cut or loose sensor wiring or defective sensor.

dPC Evaporator temperature sensor connection shorted. Check for a short in sensor wiring ordefective sensor.

 

Pc Water temperature sensor connection shorted. Check for a short in sensor wiring or defective sensor.

 

FS Heat pump in defrost cycle.

PLE or CSE EEPROM memory data loss. Hold down the SELECT key until the error message disappears. The control will be reinitiated to factory default. Re-enter the setpoints.

SPi Defective controller, remove power and restart. If error is still present, replace controller.

 

Links Company Technical Information Newsletter Social Media
       
Identity Verified - Assured Network Solutions Member of the Solar Energy Industries Association PoolHeatPumps.com, Swimming Pool Equipment & Supplies, Hinsdale, IL
Online Payment Service
Member of the American Solar Energy Society International Solar Energy Society
Poolheatpumps.com Inc.  •   105 Orchard Drive, South Haven, MI 49090   •   United States of America
© 2013 Poolheatpumps.com.  All Rights Reserved.